The Copper Tubes for Heat Exchangers and Locomotives offered by us have high thermal conductivity, resistance against corrosion and high strength. The copper used for manufacturing these tubes is a preferred primary metal for heat exchangers (radiators) and condensers since the dawn of cars and trucks.

Our copper tubes are also used to make smaller, lighter and stronger copper radiators. These radiators will be far more environmentally friendly because they are lead free and easier and cleaner to produce. Made with a non-toxic, low temperature allow based on the CuNiSnP system, these can be brazed in the same vacuum and controlled atmosphere furnaces used for aluminum radiators and at the same temperature (approx. 600°C). And since flux isn't present, cleaning after brazing isn't needed and no dangerous metals remain in the brazing material.

Our range of Copper Tubes for Automobile Industries has certain advantages over other metals. Copper had been proved since the early days to have many good attributes including easy bending and high corrosion resistance.

Copper's inherent superiority in thermal conductivity, corrosion resistance and strength has made it a preferred primary metal for radiators since the dawn of cars and trucks. Now, with new technologies, it can be used to make smaller, lighter and stronger copper radiators. These radiators will be far more environmentally friendly because they are lead free and easier and cleaner to produce. Additional increased copper content results from a number of accessories being electric instead of hydraulic. Power steering and braking are achieved electrically and the efficiency and performance of these two technologies make them candidates for installation on internal combustion vehicles in the near future. Heating and air conditioning are also achieved electrically and in some cases with a heat pump.

Electric Vehicles and even hybrid electric vehicles will use approximately twice as much copper as a conventional vehicles and this will provide the added advantage of excellent recyclables when the vehicle is removed from service.

We are reckoned amongst the trusted manufacturers and exporters of a wide range of Copper Tubes for Marine Applications. These are widely utilized in the design of seawater systems due to their excellent resistance to corrosion and befouling. Copper is widely used in applications like freshwater and seawater supply lines, heat exchangers, condensers, shafting, valve stems, and marine hardware - in which resistance to seawater, hydrated salt deposits, and befouling from marine organisms is important.

Properties of copper:

• Copper corrodes at negligible rates in unpolluted air, water, and deaerated non-oxidizing acids.

• Copper alloy artifacts have been found in nearly pristine condition after having been buried in the earth for thousands of years, and copper roofing in rural atmospheres has been found to corrode at rates of less than 0.4 mm in 200 years.

• Copper alloys resist many saline solutions, alkaline solutions, and organic chemicals.

• Copper is susceptible to more rapid attack in oxidizing acids, oxidizing heavy-metal salts, sulfur, ammonia (NH3), and some sulfur and NH3 compounds.

We manufacture and export a wide range of Copper Stripe, Rods and Plates for earthing System. Our range includes Copper Bonded Earth Plates / Lattice Copper, Couplers, Clamps, Air Terminal Base, Copper Bonded Earth Rods, Copper Bonded Earth Sheets / Lattice Copper and Driving Heads / Studs / Tips / Dowell Pins.

Copper Strips, Plates and Solid Rods are manufactured from highly conductive EC Grade Copper. They offer great resistance to corrosion. They are ideally used in applications where the salt content in the soil is very high.
Size: 16mm - 2Omm (length as per customer specifications).

Swaged Earth Rods (250 Microns)

• Plain Swaged Earth Rods.

• Tapered Swaged Earth Rods.

Driving Heads / Studs / Tips / Dowell Pins
Manufactured from high tensile steel to ensure force from power hammer. Dowell Pins are also made from high grade brass.
Sizes: 1Omm, 14mm, 5/8", 3/4" etc.

Couplers

• Material: Copper Alloy
• Sizes: 14mm, 5/8", 3/4" etc.

Clamps

• Material: Copper Alloy
• Sizes: 14mm, 3/8", 5/8", 3/4" etc.

• Material: Body casted from brass
• Application: Used as a base for fixing air terminal

Copper Bonded Earth Rods

They are manufactured from Structural Quality High Tensile Steel Grade 43A to BS 4360. These rods are molecularly bonded with pure EC Grade Copper (99.9%).

Copper Bonded Earth Sheets / Lattice Copper

• High Tensile Smooth Surface Steel Sheets are molecularly bonded with pure EC Grade Copper (99.9%).Ideal for earthing purposes
• Sizes: 1.5mm, 3mm Thickness (Length and Breadth as per customer specification)

Copper Bonded Earth Plates / Lattice Copper

• Material: Copper Alloy
• Application: Used for forming straight through, Tee and Cross joints.
• Sizes: (Light, Medium, Heavy, Rectangular, Cross)
• Metric: 16 x 3, 19 x 3, 25 x 3, 40 x 5, 50 x 6
• Imperial: (Light, Medium, Heavy, Rectangular, Cross)